Product ID:EPOXY 2000X NON-SKID DECK COATING PART A
MSDS Date:10/29/1986
FSC:8010
NIIN:01-278-1557
Kit Part:Y
MSDS Number: BNTSR

AMERICAN ABRASIVE METALS CO

460 COIT ST
IRVINGTON, NJ 07111
US

Emergency Phone: 201-373-7060

Info Phone: 201-373-7060

Cage: AMABR

AMERICAN ABRASIVE METALS COMPANY

IRVINGTON, NJ 07111 US

Telephone: 201-373-7060

Cage: AMABR

EPOXY RESINS

CAS: 25068-38-6

RTECS: KC2100000

Fraction By Weight: 12+-1%

XYLENES

CAS: 1330-20-7

RTECS: ZE2100000

Fraction By Weight: 10+-1%

OSHA PEL 100 PPM

ACGIH TLV: 100 PPM

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

PROPYLENE GLYCOL MONOMETHYL ETHER

CAS: 107-98-2

RTECS: UB7700000

Fraction By Weight: 1%

OSHA PEL 100 PPM

ACGIH TLV: 100 PPM

SILICON DIOXIDE, CRYSTALLINE

CAS: 14808-60-7

RTECS: VV7330000

Fraction By Weight: 20%

OSHA PEL SEE TABLE Z3

ACGIH TLV: 0.1 MG/M3 RDUST;9293

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:INHALATION: DIZZINESS,
UNCONSCIOUSNESS. SKIN CONTACT: IRRITATION, SENSITIZATION. EYE
CONTACT: IRRITATION, EYE DAMAGE.
Medical Cond Aggravated by Exposure:RESPIRATORY DISEASES, SKIN
CONDITIONS, KIDNEY, LIVER DISEASE.

First Aid:EYES: FLUSH WITH LARGE AMOUNTS OF WATER. GET MEDICAL
ATTENTION. INHALATION: FRESH AIR, OXYGEN, ARTIFICIAL RESPIRATION.
SKIN: WASH WITH SOAP AND WATER. INGESTION: DO NOT INDUCE VOMITING.
CALL PHYSICIAN .

Flash Point Method:PMCC
Flash Point:81.0F,27.2C
Lower Limits:1%
Upper Limits:12%
Extinguishing Media:CHEMICAL FOAM, DRY CHEMICAL.
Fire Fighting Procedures:SELF-CONTAINED BREATHING APPARATUS WITH FULL
FACE PIECE, POSITIVE PRESSURE MODE.
Unusual Fire/Explosion Hazard:VAPORS ARE HEAVIER THAN AIR; MAY TRAVEL
ALONG GROUND AND BE IGNITED BY FLAMES, SPARKS OR OTHER IGNITION
SOURCES.

Spill Release Procedures:ELIMINATE ALL IGNITION SOURCES
(FLAMES/FLARES/PILOT LIGHTS/ELECTRICAL SPARKS).

Handling and Storage Precautions:WARNING! IRRITANT: DO NOT GET INTO
EYES. AVOID CONTACT WITH SKIN/CLOTHING. AVOID INHALATION OF
VAPORS/MIST. USE W/ADEQUATE VENTIALTION.
Other Precautions:CAUTION: WHEN REMOVING OLD COATING BY SANDING OR
SANDBLASTING, WEAR PROPER DUST MASKS TO AVOID INHALATION OF SILICA
DUST. AVOID EXTREME HEAT-KEEP AWAY FROM FLAME. DO NOT EXCEED 110 F
IN STORAGE AREA.

Respiratory Protection:IF TLV'S ARE EXCEEDED, SELF-CONTAINED BREATHING
APPARATUS.
Ventilation:LOCAL AND MECHANICAL EXHAUST: SUFFICIENT TO MAINTAIN LEVEL
BELOW TLV.
Protective Gloves:RUBBER OR BUNA N
Eye Protection:CHEMICAL SPLASH GOGGLES
Other Protective Equipment:TO PREVENT REPEATED OR PROLONGED SKIN
CANTACT, WEAR PROTECTIVE CLOTHING.
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING, BEFORE
EATING/DRINKING/SMOKING. REMOVE CONTAMINATED CLOTHING AND WASH
BEFORE REUSE.
Supplemental Safety and Health

Boiling Pt:B.P. Text:>240F,>116C
Vapor Pres:8 @ 68 F
Vapor Density:3.7
Spec Gravity:2.1 (WATER=1)
Evaporation Rate & Reference:.7 (BU AC=1)
Solubility in Water:SLIGHT
Appearance and Odor:VISCOUS PASTE, MILD ODOR.

Stability Indicator/Materials to Avoid:YES
STRONG ACID, ALKALIES, AMINES, OXIDIZING AGENTS.
Hazardous Decomposition Products:CARBON DIOXIDE, CARBON MONOXIDE, TOXIC
FUMES WHEN BURNING.

Waste Disposal Methods:ABSORB ON SAND, CLAY OR OTHER ABSORBANT MATERIAL
AND SHOVEL IN TO CONTAINERS. DISPOSE BY CONTROLLED BURNING OR
AUTHORIZED LANDFILL.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.